Subwoofer Enclosure Cut Sheets

Save a little money and get a little dirty. Engulf yourself in the entirety of DIY with our Enclosure Cut Sheets. Not only do you save money, you learn and have a box that is a perfect fit for your new, or old SoundQubed or Audioque sub.

Sealed enclosures recommended for:
  • SoundQubed HDS200, HDS300
  • Audioque SDC2.0 and SDC2.5"
Ported enclosures recommended for:
  • SoundQubed HDS200, HDS300, HDC3, HDC3.1, HDC4
  • Audioque SDC2.5, HDC3 and HDC4
Note: All ported enclosures are tuned at 35hz, incorporate 45 degree corners to help with structure and to cut down on any loading issues that could occur.

8" Enclosures
10" Enclosures
12" Enclosures
15" Enclosures
18" Enclsorues

Q: What makes this different than one of the many inexpensive enclosures I can buy pre-built?
A: EVERYTHING! These are specifically designed and tuned for our woofers. They have the port area, internal area and port length needed to supply these large woofers with the air they demand and offer bracing to help stabilize the enclosure. You'll actually find out that this will be cheaper and more fun to build than going out and purchasing a prefabricated box that isn't suitable for your new and or used SoundQubed or Audioque subwoofer.
**Other subwoofers can be used in our enclosure, just check with the manufacturer or give us a shout.

Q: I don't have the tools necessary what do I do?
A: Great Question! You can print off the sheet, take it to any home improvement store and have them cut the sheets for you.

Q: What will I need to finish my enclosure?
A: You will need wood glue, a brad nailer or a drill and wood screws, clamps, a face mask (recommended) and some muscle. If you don't have a brad nailer you could hand nail as well. We suggest #8 wood screw at least 2 1/4" long.

Q: GLUE? HOW MUCH?
A: Lay your glue bead across all edges that connect and press firmly together. Don't worry about excess glue at this point it can be wiped away after you clamp the box together. We suggest getting clamps like these. Make sure to clamp in a # pattern.

Q: I don't know how many nails/screws to use!
A: No worries there isn't a page in your science book that tells us how many and where. Once the glue has settled for 10-15 minutes or longer depending on your weather conditions go around the connecting edges and make a mark every inch to two inches. Each tick is where you will place a screw or nail. Once you build a couple you'll be able to slap the nails/screws in by judgement.

Q: Uh... One of my nails/screws broke through the other side.
A: It happens to the best of us. If you can remove it if not leave it and bend off the end that is sticking out and fill it with a wood glue and saw dust mix or or epoxy.

Q: I've got it glued and screwed, now what? 
A: Assuming you had the circle cut out done at the hardware store or you have already done it with a router or a jig saw you are now ready to drop in your woofer(s). Wire them up and place them in the box, center them to your liking and screw them in.

Q: I went to put the woofer in and noticed there's no outlet for the wires to run to my amp.
A: Drill a 5/16th - 5/8th inch hole depending on the wire thickness and amount of wires in the area you want the wires to protrude from, run the wires through and fill any open space with epoxy or silicone.
Note: You can cut in plastic wire terminal cup but we don't recommend it - they add resistance and usually fail.

Q: What if... Just listen... I was mounting the woofer and I accidentally poked a hole in the rubbery foam thing?
A: The rubber foam thing is what we call a surround. It is an essential part of the woofer and damage can cause failure but normally a little pin hole from a screw won't make a difference as long as we take care of. Tip: Using black silicone squeeze a little bit onto a piece of cardboard now dab your finger in it and spread an even amount on the front making sure there are no high spots now do this for the back. Once it dries you should be good to go.

Q: What if the question I have isn't answered here?
A: No worries we have techs ready to answer. You can call us at 405-600-1936 or email tech@soundqubed.com